ARTICLE

Feasibility of high slag utilization in cementitious materials through compressive strength prediction and genetic algorithm optimization

The incorporation of supplementary cementitious materials and advanced curing conditions in cement-based composites introduces complex nonlinear interactions that strongly influence compressive strength development. Accurate prediction and optimization of compressive strength are therefore essential for efficient mixture design and sustainable construction. Based on an experimental investigation, the present study proposes a modeling framework that integrates machine learning with Genetic Algorithm optimization and k-fold cross-validation to predict and optimize the compressive strength of slag-based cementitious systems. The experimental data comprising 135 experimental results collected from the authors’ previous studies, was used to develop the predictive models. Cement pastes were prepared using CEM I 52.5N and GGBS, with GGBS replacement levels of 0, 30, 50, and 70%. The Blaine specific surface area of the GGBS was set at 250, 310, 410, and 500 m2/kg. Three water-to-binder ratios were considered: 0.35, 0.40, and 0.45. The specimens were cured at three different temperatures: 20, 40, and 60°C. Compressive strength tests were carried out at curing ages of 1, 3, 7, 28, and 90 days. The results showed that slag content has a significant influence on compressive strength development. At early curing ages, increasing slag content may reduce compressive strength because of its slower initial reactivity. However, as curing progresses, the contribution of slag becomes increasingly beneficial. Genetic algorithm optimization identified an optimal mixture characterized by a curing temperature of 41°C, a curing age of 90 days, a water-to-binder ratio of 0.36, a slag content of approximately 50%, and a slag fineness of 312 m2/kg. This mixture is predicted to achieve a compressive strength of approximately 94.94 MPa, which is higher than the values obtained for all the experimentally tested mixtures. These findings suggest that increasing slag content up to 50% may be feasible without significant compressive strength reduction under the investigated conditions, while also providing environmental and economic benefits. Overall, the proposed framework provides an accurate, interpretable, and efficient tool for compressive strength prediction and sustainable mix-design optimization of slag-based cementitious materials.

1  Introduction

The increasing environmental impacts associated with industrial activities—particularly the significant rise in carbon dioxide (CO2) emissions, the accelerated depletion of natural resources, and the continuous growth in energy consumption—pose major

...
References

1. Tan C, Yu X, Guan Y. A technology-driven pathway to net-zero carbon emissions for China’s cement industry. Appl Energy. 2022;325(1):119804. doi:10.1016/j.apenergy.2022.119804.

2. Supriya, Chaudhury R, Sharma U, Thapliyal PC, Singh LP. Low-CO2 emission strategies to achieve net zero target in cement sector. J Clean Prod. 2023;417(14):137466. doi:10.1016/j.jclepro.2023.137466.

3. Huang J, Sabri MMS, Ulrikh DV, Ahmad M, Alsaffar KAM. Predicting the compressive strength of the cement-fly ash-slag ternary concrete using the firefly algorithm (FA) and random forest (RF) hybrid machine-learning method. Materials. 2022;15(12):4193. doi:10.3390/ma15124193.

4. Turner LK, Collins FG. Carbon dioxide equivalent (CO2-e) emissions: a comparison between geopolymer and OPC cement concrete. Constr Build Mater. 2013;43(9):125–30. doi:10.1016/j.conbuildmat.2013.01.023.

5. Swathi B, Vidjeapriya R. Influence of precursor materials and molar ratios on normal, high, and ultra-high performance geopolymer concrete—a state of art review. Constr Build Mater. 2023;392(2019):132006. doi:10.1016/j.conbuildmat.2023.132006.

6. Almutairi AD, Elsayed M, Abdelaziz MM, Dahish HA. Punching shear capacity of rubberized high strength concrete slabs containing waste glass powder as cement substitute. Structures. 2025;78(21):109222. doi:10.1016/j.istruc.2025.109222.

7. Akintayo BD, Babatunde OM, Akintayo DC, Olanrewaju OA. Transforming industrial waste into low-carbon cement: a multi-criteria assessment of supplementary cementitious materials for sustainable concrete design. Recycling. 2025;10(6):211. doi:10.3390/recycling10060211.

8. Ben Haha M, Lothenbach B, Le Saout G, Winnefeld F. Influence of slag chemistry on the hydration of alkali-activated blast-furnace slag: Part I: effect of MgO. Cem Concr Res. 2011;41(9):955–63. doi:10.1016/j.cemconres.2011.05.002.

9. Özbay E, Erdemir M, DurmuŞHİ. Utilization and efficiency of ground granulated blast furnace slag on concrete properties–a review. Constr Build Mater. 2016;105(1511):423–34. doi:10.1016/j.conbuildmat.2015.12.153.

10. Gao JM, Qian CX, Liu HF, Wang B, Li L. ITZ microstructure of concrete containing GGBS. Cem Concr Res. 2005;35(7):1299–304. doi:10.1016/j.cemconres.2004.06.042.

11. Bougara A, Lynsdale C, Milestone NB. The influence of slag properties, mix parameters and curing temperature on hydration and strength development of slag/cement blends. Constr Build Mater. 2018;187(4):339–47. doi:10.1016/j.conbuildmat.2018.07.166.

12. Ren Z, Li D. Application of steel slag as an aggregate in concrete production: a review. Materials. 2023;16(17):5841. doi:10.3390/ma16175841.

13. Amin MN, Khan K, Saleem MU, Khurram N, Niazi MUK. Influence of mechanically activated electric arc furnace slag on compressive strength of mortars incorporating curing moisture and temperature effects. Sustain Switz. 2017;9(8):1178. doi:10.3390/su9081178.

14. Abdalkader A, Farag M. Impact of curing temperature on the compressive strength of cement mortars incorporating electric arc furnace slag. Univ Zawia J Eng Sci Technol. 2025;3(2):172–81. doi:10.26629/uzjest.2025.14.

15. Bougara A, Lynsdale C, Milestone NB. Reactivity and performance of blastfurnace slags of differing origin. Cem Concr Compos. 2010;32(4):319–24. doi:10.1016/j.cemconcomp.2009.12.002.

16. Kellouche Y, Djebien R, Laouissi A, Karmi Y, Hani M, Tayeh BA, et al. Prediction and optimization of the compressive strength of marble powder-based concrete using AI techniques: machine learning and metaheuristic approaches. Model Earth Syst Environ. 2025;11(6):413. doi:10.1007/s40808-025-02590-x.

17. Kellouche Y, Boukhatem B, Ghrici M, Rebouh R, Zidol A. Neural network model for predicting the carbonation depth of slag concrete. Asian J Civ Eng. 2021;22(7):1401–14. doi:10.1007/s42107-021-00390-z.

18. Kellouche Y, Ghrici M, Boukhatem B. Service life prediction of fly ash concrete using an artificial neural network. Front Struct Civ Eng. 2021;15(3):793–805. doi:10.1007/s11709-021-0717-9.

19. Kellouche Y, Tayeh BA, Chetbani Y, Zeyad AM, Mostafa SA. Comparative study of different machine learning approaches for predicting the compressive strength of palm fuel ash concrete. J Build Eng. 2024;88:109187. doi:10.1016/j.jobe.2024.109187.

20. Qayyum Khan A, Ahmad Awan H, Rasul M, Ahmad Siddiqi Z, Pimanmas A. Optimized artificial neural network model for accurate prediction of compressive strength of normal and high strength concrete. Clean Mater. 2023;10(2):100211. doi:10.1016/j.clema.2023.100211.

21. Mustapha IB, Abdulkareem M, Jassam TM, AlAteah AH, Al-Sodani KAA, Al-Tholaia MMH, et al. Comparative analysis of gradient-boosting ensembles for estimation of compressive strength of quaternary blend concrete. Int J Concr Struct Mater. 2024;18(1):20. doi:10.1186/s40069-023-00653-w.

22. Singh T, Jindal S, Kumar A, Ahuja R. Prediction modelling and sensitivity analysis for mechanical properties for SCMs based on no fines concrete. Innov Infrastruct Solut. 2026;11(9):512. doi:10.1007/s41062-026-02904-7.

23. Rathakrishnan V, Beddu SB, Ahmed AN. Predicting compressive strength of high-performance concrete with high volume ground granulated blast-furnace slag replacement using boosting machine learning algorithms. Sci Rep. 2022;12(1):9539. doi:10.1038/s41598-022-12890-2.

24. Elshaarawy MK, Alsaadawi MM, Hamed AK. Machine learning and interactive GUI for concrete compressive strength prediction. Sci Rep. 2024;14(1):16694. doi:10.1038/s41598-024-66957-3.

25. Vargas JF, Oviedo AI, Ortega NA, Orozco E, Gómez A, Londoño JM. Machine-learning-based predictive models for compressive strength, flexural strength, and slump of concrete. Appl Sci. 2024;14(11):4426. doi:10.3390/app14114426.

26. Yu Y, Al-Damad IMA, Foster S, Nezhad AA, Hajimohammadi A. Compressive strength prediction of fly ash/slag-based geopolymer concrete using EBA-optimised chemistry-informed interpretable deep learning model. Dev Built Environ. 2025;23(1):100736. doi:10.1016/j.dibe.2025.100736.

27. Yu Y, Jayathilakage R, Liu Y, Hajimohammadi A. Intelligent compressive strength prediction of sustainable rubberised concrete using an optimised interpretable deep CNN-LSTM model with attention mechanism. Appl Soft Comput. 2025;185:113993. doi:10.1016/j.asoc.2025.113993.

28. Van Dao D, Trinh SH, Ly HB, Pham BT. Prediction of compressive strength of geopolymer concrete using entirely steel slag aggregates: novel hybrid artificial intelligence approaches. Appl Sci. 2019;9(6):1113. doi:10.3390/app9061113.

29. Alnaqbi A, Al-Khateeb GG, Zeiada W. Advanced prediction of spalling in rigid pavements using GBM and GA optimization. Discov Cities. 2025;2(1):87. doi:10.1007/s44327-025-00129-4.

30. Bougara A. Characterization and investigation of the mechanical and calorimetric behavior of El-Hadjar slag [dissertation]. Bir El Djir, Algeria: University of Sciences and Technology of Oran (USTO); 2008.

31. Khan MA, Farooq F, Javed MF, Zafar A, Ostrowski KA, Aslam F, et al. Simulation of depth of wear of eco-friendly concrete using machine learning based computational approaches. Materials. 2021;15(1):58. doi:10.3390/ma15010058.

32. Kline RB. Principles and practice of structural equation modelling. 4th ed. New York, NY, USA: Guilford Publications; 2015.

33. Bilim C, AtiŞ CD, Tanyildizi H, Karahan O. Predicting the compressive strength of ground granulated blast furnace slag concrete using artificial neural network. Adv Eng Softw. 2009;40(5):334–40. doi:10.1016/j.advengsoft.2008.05.005.

34. Cutler DR, Edwards TC Jr, Beard KH, Cutler A, Hess KT, Gibson J, et al. Random forests for classification in ecology. Ecology. 2007;88(11):2783–92. doi:10.1890/07-0539.1.

35. Friedman JH. Greedy function approximation: a gradient boosting machine. Ann Statist. 2001;29(5):1189–232. doi:10.1214/aos/1013203451.

36. Hu H, Jiang M, Tang M, Liang H, Cui H, Liu C, et al. Prediction of compressive strength of fly ash-based geopolymers concrete based on machine learning. Results Eng. 2025;27:106492. doi:10.1016/j.rineng.2025.106492.

37. Rasmussen CE, Williams CKI. Gaussian processes for machine learning. Cambridge, MA, USA: The MIT Press; 2005. doi:10.7551/mitpress/3206.001.0001.

38. Yu Y, Wang G, Huseien GF, Zou Z, Ding Z, Zhang C. Intelligent prediction of compressive strength of self-compacting concrete incorporating silica fume using hybrid IWOA-GPR model. Mater Today Commun. 2025;45:112282. doi:10.1016/j.mtcomm.2025.112282.

39. Zhao T, Song C, Lu S, Xu L. Prediction of uniaxial compressive strength using fully Bayesian Gaussian process regression (fB-GPR) with model class selection. Rock Mech Rock Eng. 2022;55(10):6301–19. doi:10.1007/s00603-022-02964-y.

40. Satyanarayana GVV, Vivek Kumar C, Karthikeyan RM, Punitha A, Vatin NI, Joshi A, et al. Machine learning prediction and optimization of compressive strength for blended concrete by applying ANN and genetic algorithm. Cogent Eng. 2024;11(1):2376914. doi:10.1080/23311916.2024.2376914.

41. Ghanemi NE, Abdeddaim M, Ounis A, Basili M. Neural network based active control of base isolated structure considering isolator nonlinearity. Front Built Environ. 2025;11:1630131. doi:10.3389/fbuil.2025.1630131.

42. Baumann D, Baumann K. Reliable estimation of prediction errors for QSAR models under model uncertainty using double cross-validation. J Cheminform. 2014;6(1):47. doi:10.1186/s13321-014-0047-1.

43. Lundberg SM, Erion G, Chen H, DeGrave A, Prutkin JM, Nair B, et al. Explainable AI for trees: from local explanations to global understanding. arXiv:1905.04610. 2019.

44. Escalante-Garcia JI, Sharp JH. The effect of temperature on the early hydration of Portland cement and blended cements. Adv Cem Res. 2000;12(3):121–30. doi:10.1680/adcr.2000.12.3.121.

45. Escalante-Garcı́a JI, Sharp JH. Effect of temperature on the hydration of the main clinker phases in Portland cements: part ii, blended cements. Cem Concr Res. 1998;28(9):1259–74. doi:10.1016/s0008-8846(98)00107-0.

46. Wang Q, Yan P, Feng J. A discussion on improving hydration activity of steel slag by altering its mineral compositions. J Hazard Mater. 2011;186(2–3):1070–5. doi:10.1016/j.jhazmat.2010.11.109.

47. Escalante-Garcı́a JI, Sharp JH. The microstructure and mechanical properties of blended cements hydrated at various temperatures. Cem Concr Res. 2001;31(5):695–702. doi:10.1016/s0008-8846(01)00471-9.

48. Pal SC, Mukherjee A, Pathak SR. Investigation of hydraulic activity of ground granulated blast furnace slag in concrete. Cem Concr Res. 2003;33(9):1481–6. doi:10.1016/s0008-8846(03)00062-0.

49. Anwar M, Emarah D. Durability of blast-furnace slag cement concrete with different curing methods. JES J Eng Sci. 2022;50(5):276–91. doi:10.21608/jesaun.2022.140887.1142.

50. Ben Haha M, De Weerdt K, Lothenbach B. Quantification of the degree of reaction of fly ash. Cem Concr Res. 2010;40(11):1620–9. doi:10.1016/j.cemconres.2010.07.004.

51. Rahhal VF, Batic OR. Mineral admixtures contribution to the development of heat of hydration and strength. Cem Concr Aggreg. 1994;16(2):150–8. doi:10.1520/cca10293j.

52. Goldberg DE. Genetic algorithms in search, optimization, and machine learning. Choice Rev Online. 1989;27(2):0936. doi:10.5860/choice.27-0936.

53. Scrivener KL, John VM, Gartner EM. Eco-efficient cements: potential economically viable solutions for a low-CO2 cement-based materials industry. Cem Concr Res. 2018;114(5):2–26. doi:10.1016/j.cemconres.2018.03.015.

54. Taylor HF. Cement chemistry. 2nd ed. Leeds, UK: Emerald Publishing Limited; 1997.

55. Shi C, Jiménez AF, Palomo A. New cements for the 21st century: the pursuit of an alternative to Portland cement. Cem Concr Res. 2011;41(7):750–63. doi:10.1016/j.cemconres.2011.03.016.

56. Chou JS, Chong WK, Bui DK. Nature-inspired metaheuristic regression system: programming and implementation for civil engineering applications. J Comput Civ Eng. 2016;30(5):04016007. doi:10.1061/(asce)cp.1943-5487.0000561.

57. Yeh IC. Modeling of strength of high-performance concrete using artificial neural networks. Cem Concr Res. 1998;28(12):1797–808. doi:10.1016/s0008-8846(98)00165-3.

Cite This Article

APA Style
Guettioui, M., Kellouche, Y., Bougara, A., Ghanemi, N. E. (2026). Feasibility of high slag utilization in cementitious materials through compressive strength prediction and genetic algorithm optimization. ZKG International, 79(7), 122–148. https://doi.org/10.32604/zkg.2026.085974
Vancouver Style
Guettioui M, Kellouche Y, Bougara A, Ghanemi NE. Feasibility of high slag utilization in cementitious materials through compressive strength prediction and genetic algorithm optimization. ZKG Int.. 2026;79(7):122–148. https://doi.org/10.32604/zkg.2026.085974
IEEE Style
M. Guettioui, Y. Kellouche, A. Bougara, and N. E. Ghanemi, “Feasibility of high slag utilization in cementitious materials through compressive strength prediction and genetic algorithm optimization,” ZKG Int., vol. 79, no. 7, pp. 122–148, 2026. https://doi.org/10.32604/zkg.2026.085974

Related articles:

×